Simple gain mechanism discovered

[hermesatar]

"hubbard coil.  what, 6 driver coils and a middle secondary. from what i had written here in another thread, i even explain the possible workings that should stand your hair on end knowing that idea. i have a pdf i have to dig up that takes you through details of why and how it is done.  ill post later this evening."
Mags

 
Hi Everyone,

Now I have measured my ET transformer. I used the Voltcraft 632 FG 30 MHz Oscilloscope to measure the voltage from the frequency generator built into the oscilloscope as well as across the 1 ohm resistors. The frequency was measured with a TES 2208 Multimeter and the inductance of the transformer coils with a Voltcraft LCR-9063. The direct current resistance in the inductances is a maximum of 0.1 ohm.

Best wishes, Hermes    

[Jim Mac]

"hubbard coil.  what, 6 driver coils and a middle secondary. from what i had written here in another thread, i even explain the possible workings that should stand your hair on end knowing that idea. i have a pdf i have to dig up that takes you through details of why and how it is done.  ill post later this evening."
Mags

 
Hi Everyone,

Now I have measured my ET transformer. I used the Voltcraft 632 FG 30 MHz Oscilloscope to measure the voltage from the frequency generator built into the oscilloscope as well as across the 1 ohm resistors. The frequency was measured with a TES 2208 Multimeter and the inductance of the transformer coils with a Voltcraft LCR-9063. The direct current resistance in the inductances is a maximum of 0.1 ohm.

Best wishes, Hermes

For simple-minds like mine, can you please post pictures of the physical setup?

[magluvin]

the file i was suppose to upload.

mags

[hermesatar]

"hubbard coil.  what, 6 driver coils and a middle secondary. from what i had written here in another thread, i even explain the possible workings that should stand your hair on end knowing that idea. i have a pdf i have to dig up that takes you through details of why and how it is done.  ill post later this evening."
Mags

 
Hi Everyone,

Now I have measured my ET transformer. I used the Voltcraft 632 FG 30 MHz Oscilloscope to measure the voltage from the frequency generator built into the oscilloscope as well as across the 1 ohm resistors. The frequency was measured with a TES 2208 Multimeter and the inductance of the transformer coils with a Voltcraft LCR-9063. The direct current resistance in the inductances is a maximum of 0.1 ohm.

Best wishes, Hermes

Kone wrote:

Hi Hermes

Wow thats pretty good!
What is the resistance in ohms of the father, the mother, and child coil?

- 0.1 ohm in each coil

How many turns in each?

- don't know. I just used 1 of 2 flyback transformer cores from an old TV.
Actually I have many flyback transformers from a surplus store.

What is thickness of wire?

- it's 0.75 mm
 
Is it just one layer?

- Yes one layer each coil.

Is it a ferrite core?  How long and what diameter?

- Yes a ferrite core from an old TV.  The core was wind 3 cm long and 1.5 cm diameter. You will find a photo of the transformer core from an old TV at:

https://www.youtube.com/watch?v=e2p58tWIxNc

- I used 1 of 4 parts of the core. It has no magnetic loop. I just wanted to test it similair to a ferrite rod with open ends.


Really good! 
Maybe those ET fuckers really do have something going on haha

I watched that Adamski video part one and two pretty interesting I always thought he fake but I have read too much garbage on internet  (like wikipedia)

I did not hear where he described this transformer design in parts one and two at least.
Where did you hear about it?

- I might remember wrong on the videos, but I do remember that Glenn Steckling said that the ET secret of free energy is to use two input coils - one clockwise wind
and the other anti clockwise wind. It was up to me to figure up what he mean.

I liked the blown up photo of the alien hiding behind hill - spooky....

I would like to try this at 60hz with laminate steel core from a MWOT instead of ferrite- maybe U-shaped?

- just remember after winding the "father coil" clockwise on the laminate steel core. You have to wind the "child coil" clockwise over (upon) the "father coil" and the "mother coil" anti clockwise over (upon) the "child coil".

Also could be awesome motor coils with "counter direction" induced  pickup winds sharing core with motor coils as described last post.

- I have no idea if it could work, maybe you can try. And I have no idea why the inductance differ between the coils. I just wind the coils a layer each. I have a suggestion. Because the voltage was so small (0.8 volt) from the "child coil". You can wind the "child coil" with more layers, maybe 4 to 7 layers more than the "father coil" and the "mother coil" Maybe it works the same as the transformer theory with different primary and secondary windings?

- Best Wishes, Hermes

- And I want to correct a mistakes I did on the et_transformer drawing. It should be 3 volts input. Not 5 volts. I have no idea why it loads down the voltage output of the frequency generator when lowering the frequency from <1MHz.

Kone

[magluvin]

thanks for the info. is it that the mother coil needs to be wound counter clockwise, or could it be clockwise and connected oppositely?

mags

[magluvin]

i have an E-core transformer that i had wound 2 equal windings on the outer legs of the E and a winding on the center. ill put some pulsing on the outer windings, first 1 then both to see if there is a diff in efficiency.

mags

[magluvin]

i found the e-core transformer.  will do some stuff with it this weekend. the outside windings are series and counter wound so they produce the same field in reference to the core orientation. 

mags

[ovun987]

Very nice!

Do you feel this is at all similar to what MTECH is doing (child, mother, father coils) with his work, hermesatar?

You might be able to glean further insight from the way he is winding and what parts he is using. Good work!

https://www.youtube.com/@MTECHINDUSTRIES2022/videos

[magluvin]

hey. well it firstly applies my reasoning of adding a second driver hopefully. will have to rewind the outer windings and make them individual for testing, as you can see they are in series connection at the top of the transformer. but ill do initial testing as is first. just going to test in and out. i have this little 2in by 1in bare bones digital square wave gen with duty cycle down to 1%. XY-LPWM. CHEAP. but has its uses and so far its been good to me. set up on a test board with interchangeable output boards. i was in my reed switch, 555 timer caveman lab days when i wound this one. my scope was the radioshack pen scope. lol. have hantek dual now and a 'hanmatek' dual plus dvm portable that i like a lot. still have my wavetek 2030 meter. in the 90s
it can measure resistance down to .01ohm, which is important in many ways. finding that shorted component on a board, measuring amplifier resistors for accuracy, etc. but he hanmatek does .01ohm too. just over 100bucks. for around 200 i believe, also has sig gen. nice bright screen. the wavetek was 320 back then. still works.

mags

---

sig gen

mags

---

i like the 'family' coil idea. may be the same or similar. will do one of those also..

mags

[hermesatar]

thanks for the info.  is it that the mother coil needs to be wound counter clockwise, or could it be clockwise and connected oppositely? 

mags

Hello magluvin. I have not tested winding the mother coil in the same direction as the father and child coils. Bad news is that, when connecting a capacitor in series with the child coil for resonance, the circuit is not above unity: 7.5 kHz Input power: 50 mA*6 volts = 0.3 watts. Output power: 400 mA*0.4 volts = 0.16 watts. I think it is phase shift in the transformer. It is inductive but the load is resistive.

But considering that the child coil is wound with the same number of turns as both the father coil and the mother coil and consumes more milliamps, maybe the et_transformer can be used as a motor coil in a permanent magnet motor? Like the Robert Adams electric motor?

http://gratisenergi.se/adams.htm

Best wishes, Hermes

P.S has anyone built a motor that consumes reactive power? I mean ampere turns?

P.S 2 all three coils must be wound on the same ferrite rod or on the same transformer leg. They must be wrapped over each other. The father coil is wound on the core, the child coil over the father coil and the mother coil over over the child coil.